PRO 120 SPRAY MULTIPRODUCT BOX

PRECAUTIONS

• Apply in temperatures between 10-30°C, 50-90°F.
• Apply in a closed, well ventilated, indoor area with air humidity not exceeding 70%
• Cover and seal all windows
• PRO 120 SPRAY requires IR Curing Lamps
• Clean spray gun with PRO SOLVENT SPRAY (Spray Gun Cleaner) between products and immediately after applying PRO HYDRO SPRAY to avoid any permanent damage to the spray gun.
• Must wear protective gloves and appropriate respirator.

WHAT YOU’LL NEED

• 4 Microfiber Towels
• Spray Gun & Diamond ProTech Adapter
• Protective Gloves
• Respirator Mask
• Diamond Body Prep

APPLICATION TIPS

• If applying in high heat or high humidity, lower time between application and removal. Test over a small area to determine appropriate time to let the coating bond to the surface.
• Apply PRO 120 A to body, headlights, rubber, and metal trim.
• Apply PRO 120 B to body, headlights, rubber, and metal trim.
• Apply PRO HYDRO to body, headlights, and metal trim, but not to rubber/plastic.
• PRO 120 A SPRAY / PRO 120 B SPRAY / PRO HYDRO SPRAY: As the coating bonds to the surface a haze will appear. This indicates the coating is ready to remove. If product dries on the surface or is difficult to remove, re-wet the area with more product and immediately buff off.

IR CURING LAMP INSTRUCTIONS:

• Temperature: 50-60°C / 120-140°F
• Distance to bodywork: 60-70 cm / 24-28 inches.
• Time: 15-20 minutes for each section.

INSTRUCTIONS

• Wash, polish and treat areas to be coated with Diamond Body Prep.
• Shake the bottle of PRO 120 SPRAY A for 15 seconds. Connect the bottle to the Diamond ProTech adapter and then to the IWATA LPH-80 spray gun. Spray PRO 120 SPRAY A evenly over 3-4 sections of the car. Partially overlap each pass over the previous to insure full coverage.
• Wait 10-15 mins and buff off excess with a low-nap microfiber towel.
• Clean the spray gun with PRO SOLVENT SPRAY to prepare for PRO 120 SPRAY B.
• Wait 1 hour to allow PRO 120 SPRAY A to bond before applying the next layer: PRO 120 SPRAY B
• Shake the bottle of PRO 120 SPRAY B well for 15 seconds. Connect bottle to the Diamond ProTech adapter and then to the IWATA LPH-80 spray gun. Spray PRO 120 SPRAY B evenly over 1-2 sections of the car. Partially overlap each pass over the previous to insure full coverage.Wait 1-3 mins and buff off excess with a low-nap microfiber towel. Clean the spray gun with PRO SOLVENT SPRAY to prepare for PRO HYDRO SPRAY.
• Diamond ProTech recommends using IR curing lamps to accelerate the curing process.
  If no IR curing lights are used, wait four hours to allow PRO 120 SPRAY B to dry before applying the next layer, PRO HYDRO SPRAY.
• Shake the bottle of PRO HYDRO SPRAY well for 15 seconds and connect the bottle to the Diamond ProTech spray adapter and then to the IWATA LPH-80 spray gun. Proceed to spray PRO HYDRO SPRAY evenly over 3-4 sections of the car. Partially overlap each spray pass over the previous one to insure full coverage.
• Wait 7-10 mins and buff off excess with a low-nap microfiber towel.
  Clean spray gun with PRO SOLVENT SPRAY when finished. Allow coating system to cure for 2 hours before using the vehicle.

• We recommend that you use an IWATA LPH-80 spray gun with 0.8mm needle.
• Clean spray gun with PRO SOLVENT SPRAY between layers and immediately after applying final layer of coating to avoid any permanent damage to the spray gun
• Recommended spray gun settings:Air nipple – 3.5
• Fluid nipple – 3.5-4.5 (depending on porousness of surface)
• Pressure – 0.1-0.2 BAR