AEROSOL PRO 120

  • 10-Year Armor Protection
  • Diamond Hard Scratch Resistance
  • Chrome-like Mirror Gloss & Rich Color Depth
  • Extreme Hydrophobic Top Coat

Los gastos de envío se calculan en la pantalla de pagos.
APPLICATION INSTRUCTIONS

PRECAUTIONS

  • Apply in temperatures between 10-30°C, 50-90°F.
  • Apply in a closed, well ventilated, indoor area with air humidity not exceeding 70%
  • Cover and seal all windows
  • PRO 120 SPRAY requires IR Curing Lamps
  • Clean spray gun with PRO SOLVENT SPRAY (Spray Gun Cleaner) between products and immediately after applying PRO HYDRO SPRAY to avoid any permanent damage to the spray gun.
  • Must wear protective gloves and appropriate respirator.

WHAT YOU’LL NEED

  • 4 Microfiber Towels
  • Spray Gun & Diamond ProTech Adapter
  • Protective Gloves
  • Respirator Mask
  • Diamond Body Prep

APPLICATION TIPS

  • If applying in high heat or high humidity, lower time between application and removal. Test over a small area to determine appropriate time to let the coating bond to the surface.
  • Apply PRO 120 A to body, headlights, rubber, and metal trim.
  • Apply PRO 120 B to body, headlights, rubber, and metal trim.
  • Apply PRO HYDRO to body, headlights, and metal trim, but not to rubber/plastic.
  • PRO 120 A SPRAY / PRO 120 B SPRAY / PRO HYDRO SPRAY: As the coating bonds to the surface a haze will appear. This indicates the coating is ready to remove. If product dries on the surface or is difficult to remove, re-wet the area with more product and immediately buff off.

IR CURING LAMP INSTRUCTIONS:

  • Temperature: 50-60°C / 120-140°F
  • Distance to bodywork: 60-70 cm / 24-28 inches.
  • Time: 15-20 minutes for each section.

INSTRUCTIONS

  • Wash, polish and treat areas to be coated with Diamond Body Prep.
  • Shake the bottle of PRO 120 SPRAY A for 15 seconds. Connect the bottle to the Diamond ProTech adapter and then to the IWATA LPH-80 spray gun. Spray PRO 120 SPRAY A evenly over 3-4 sections of the car. Partially overlap each pass over the previous to insure full coverage.
  • Wait 10-15 mins and buff off excess with a low-nap microfiber towel.
  • Clean the spray gun with PRO SOLVENT SPRAY to prepare for PRO 120 SPRAY B.
  • Wait 1 hour to allow PRO 120 SPRAY A to bond before applying the next layer: PRO 120 SPRAY B
  • Shake the bottle of PRO 120 SPRAY B well for 15 seconds. Connect bottle to the Diamond ProTech adapter and then to the IWATA LPH-80 spray gun. Spray PRO 120 SPRAY B evenly over 1-2 sections of the car. Partially overlap each pass over the previous to insure full coverage.Wait 1-3 mins and buff off excess with a low-nap microfiber towel. Clean the spray gun with PRO SOLVENT SPRAY to prepare for PRO HYDRO SPRAY.
  • Diamond ProTech recommends using IR curing lamps to accelerate the curing process.
    If no IR curing lights are used, wait four hours to allow PRO 120 SPRAY B to dry before applying the next layer, PRO HYDRO SPRAY.
  • Shake the bottle of PRO HYDRO SPRAY well for 15 seconds and connect the bottle to the Diamond ProTech spray adapter and then to the IWATA LPH-80 spray gun. Proceed to spray PRO HYDRO SPRAY evenly over 3-4 sections of the car. Partially overlap each spray pass over the previous one to insure full coverage.
  • Wait 7-10 mins and buff off excess with a low-nap microfiber towel.
    Clean spray gun with PRO SOLVENT SPRAY when finished. Allow coating system to cure for 2 hours before using the vehicle.
SPRAY GUN SETTINGS & INSTRUCTIONS
  • We recommend that you use an IWATA LPH-80 spray gun with 0.8mm needle.
  • Clean spray gun with PRO SOLVENT SPRAY between layers and immediately after applying final layer of coating to avoid any permanent damage to the spray gun
  • Recommended spray gun settings:Air nipple – 3.5
  • Fluid nipple – 3.5-4.5 (depending on porousness of surface)
  • Pressure – 0.1-0.2 BAR

Nuestro sistema de recubrimiento de 10 años

PRO 120 SPRAY ofrece una protección de primera línea y un aspecto estético, al tiempo que permite al detallista la capacidad de trabajar de una manera cómoda y eficiente. Se combinan polímeros 100 % inorgánicos infundidos con billones de partículas de nanodiamantes para crear un acabado que asombrará.

PRO 120 SPRAY es un recubrimiento de nanodiamantes de primera línea y de varias etapas. Utilizando nuestra combinación más sofisticada de compuestos de nanodiamantes enriquecidos, PRO 120 crea una inmensa protección, resistencia a los arañazos y una rica profundidad de color .

Combinado con PRO HYDRO , nuestro acabado hidrofóbico de larga duración, este paquete crea un brillo intenso como un espejo y una suavidad irresistible. Con la preparación adecuada, PRO 120 SPRAY brindará hasta 10 años de protección hidrofóbica endurecida.


Customer Reviews

Be the first to write a review
0%
(0)
0%
(0)
0%
(0)
0%
(0)
0%
(0)